| 型號 | 品牌 | 功能應用 |
|---|
| MAX6310UK47D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.583(min),4.818(max). Nominal timeout period 140ms. |
| MAX6316LUK48AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reser output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX251CSD | MaximIC | +5V powered isolated RS-232 driver/receiver. |
| MAX6316LUK26DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1120ms, typ watchdog timeout 1.6sec |
| MAX4610CUD | MaximIC | Low-voltage, quad, SPST, CMOS analog switches (four NO switches). |
| MAX5541ESA | MaximIC | Low-cost, +5V, serial-input, voltage-output, 16-bit DAC. |
| MAX311MJE | MaximIC | CMOS RF/video multiplexer (2-of-8, 4 channel differential). |
| MAX6318LHUK44DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.390V min, reset timeout 1.12sec,typ watchdog timeout 25.6sec |
| MAX636AEPA | MaximIC | Preset -12V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 5%. |
| MAX642ACSA | MaximIC | +12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy |
| MAX383EJE | MaximIC | Precision, low-voltage analog switch. |
| MAX6241BEPA | MaximIC | Low-noise, precision, +4.096V output voltage reference. Max TEMPCO (ppm/C) 7.0. |
| MAX921EPA | MaximIC | Single micropower, low-voltage comparator. Internal 1.182V+-1% voltage rsference Internal programmable hysteresis. |
| MAX1232CPA | MaximIC | Microprocessor monitor |
| MAX735CPA | MaximIC | Negative output, inverting, current-mode PWM regulator. Converts +4V to +6.2V input to -5V output. |
| MXD1000PD30 | MaximIC | 5-tap silicon delay line |
| MAX766CSA | MaximIC | -15V or adjustable output from -1V to -16V, high-efficiency, low IQ DC-DC inverter |
| MAX6316LUK39DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX111AEAP | MaximIC | Low-cost, 2-channel, 14-bit serial ADC. |
| MAX4213EUA | MaximIC | Single, miniature, 300MHz -3dB bandwidth, single 3.3V/5.0V operation, Rail-to-Rail op amp with enable. |
| MAX6320PUK48CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MX752KCSE | MaximIC | CMOS 8-bit buffered multiplying DAC. TTL/CMOS compatible at +5V. Error +-1/4 LSB |
| ICL7667CBA | MaximIC | Dual power MOSFET driver. |
| MAX548ACUA | MaximIC | +2.5V to +5.5V, low-power, dual 8-bit voltage-output DAC with an asynchronous load input; it uses Vdd as the reference input. . |
| MAX153C/D | MaximIC | 1Msps, microprocessor-compatible, 8-bit ADC with 1microA power-down. |
| MAX4186EEE | MaximIC | =2. |
| MAX177CNG | MaximIC | CMOS 10-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX6321HPUK47DY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| ICL7129AC/D | MaximIC | 4-1/2 digit single-ship A/D converter with LCD driver |
| MAX4429CPA | MaximIC | High-speed, 6A single MOSFET driver. 4.5V t0 18V supply range. |
