| 型號 | 品牌 | 功能應用 |
|---|
| MAX6320PUK29CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX5158CEE | MaximIC | Low-power, dual, 10-bit voltage-output DAC with internal gain of +2V/V. +5V single-supply operation. |
| MAX264ACWI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| ICL8069CCZQ2 | MaximIC | Low-voltage reference, 50 ppm/C - max temp. coefficient. |
| MX7226KP | MaximIC | CMOS quad 8-bit D/A converter with separate input registers. Error +-2 LSB. |
| MX7845SE | MaximIC | Complete, 12-bit multiplying DAC. 4-quadrant multiplication. |
| MAX4523MJE | MaximIC | Quad, low-voltage, SPST analog switch. |
| MAX170DCPA | MaximIC | Serial output 5.6 microsec 12-bit A/D converter. Error +-1 LSB. |
| MAX1632EAI | MaximIC | Multi-output, low-noise power-supply controller for notebook computers. |
| MAX6306UK35D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.413(min),3.588(max) Nominal timeout period 1120ms. |
| MXD1005PA175 | MaximIC | 5-tap silicon delay line |
| MAX773MJD | MaximIC | 5V, 12V,15V or adjustable, high-efficiency, low IQ, step-up DC-DC controller |
| MAX4536ESE | MaximIC | Quad, low-voltage, SPST analog switches with enable. 4 NO. |
| MAX6326UR23-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 2.320V. Standard version, order increment 2500 |
| ICL8069DCSQ2 | MaximIC | Low-voltage reference, 100 ppm/C - max temp. coefficient. |
| MAX151ACNG | MaximIC | 300kHz 10-bit A/D converter with reference and T/H. TUE 1.0 LSB. |
| MAX6316LUK33BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.300V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX2685EEE | MaximIC | Low-cost, 900MHz, low-noise amplifier and downconverter mixer. |
| MAX6190CESA | MaximIC | Precision, micropower, low-dropout voltage reference. Output voltage 1.250V, initial accuracy +-6, temperature coefficient <25ppm. |
| MAX3237EEAI | MaximIC | +-15kV ESD-protected, down to 10nA, 3.0V to5.5V, up to 1Mbps, true RS-232 transceiver. |
| MAX6307UK44D1-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds4.270(min),4.490(max).Nominal timeout period 1ms. |
| MF10CN | MaximIC | Dual universal switched capacitor filter. |
| MAX4118ESA | MaximIC | Dual, 300MHz -3dB bandwidth, low-power, current feedback amplifier. |
| MAX688CSA | MaximIC | High-accuracy, low-dropout linear regulator |
| MAX543AESA | MaximIC | CMOS, 12-bit, serial-input multiplying DAC. Linearity (LSB) +-1/2 |
| MAX6318LHUK35DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.500V min, reset timeout 1.12sec,typ watchdog timeout 6.3ms |
| MAX704CPA | MaximIC | Low-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.40V. |
| MAX857C/D | MaximIC | Adjustable-output, step-up DC-DC converter. Adjustable version 0.8V to 6.0V input voltage, output voltage 2.7V to 6.0V range. |
| DG425DN | MaximIC | Improved low-pover, CMOS analog switches with latches |
| MAX485ECSA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
