| 型號 | 品牌 | 功能應用 |
|---|
| MAX243CWE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6318LHUK29CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.930V min, reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX3471EUA | MaximIC | 1.6microA, RS-485/RS-422, half-duplex, differential transceiver for battety-powered systems |
| MAX806RCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX6320PUK41BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MAX6320PUK42BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX7403EPA | MaximIC | 8-th-order, lowpass, elliptic, switched-capacitor filter. Filter response elliptic (r=1.2), operating voltage +5V |
| MAX7405CPA | MaximIC | 8-th-order, lowpass, bessel, switched-capacitor filter. Single-supply operation +3V |
| MAX6322HPUK35A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1ms |
| MAX6307UK25D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds2.438(min),2.563(max).Nominal timeout period 1120ms. |
| MAX144BMJA | MaximIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-1 |
| MAX199BEAI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX7219CNG | MaximIC | Serially interfaced, 8-digit LED display driver. |
| MAX4275AHESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz. |
| MAX6318LHUK32CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.200V min, reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX4373TEUA | MaximIC | Low-cost, micropower, high-side current-sense amplifier + comparator + reference IC. Gain +20V/V. |
| MAX6316MUK40AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX263ACPI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX3244CWI | MaximIC | 1microA supply current, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus |
| MAX6320PUK45BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MX7520TD | MaximIC | CMOS 10 bit multiplying D/A converter. Error 0.1% |
| MAX436MJD | MaximIC | Wideband transconductance amplifier. 200MHz bandwidth. |
| MAX379MLP | MaximIC | High-voltage, fault-protected analog multiplexer. |
| ICL7106CPL | MaximIC | 3 1/2 digit a/d converter |
| MAX4133ESD | MaximIC | Dual, wide-bandwidth, low-power, +2.7V to +6.5V single-supply operation, Rail-to-Rail I/O op amp. 25microA shutdown function. |
| MAX393EJE | MaximIC | Precision, quad, SPST analog switch |
| MAX6321HPUK30AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX4555CSE | MaximIC | Force-sense switches (four indepedent SPST NC switches, two force switches, and two sense switches). |
| MAX6321HPUK45CW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6318LHUK30DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.000V min, reset timeout 1.12sec, typ watchdog timeout 6.3ms |
