| 型號 | 品牌 | 功能應用 |
|---|
| MAX6312UK37D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.608(min) 3.793(max). Nominal timeout period 1ms. |
| MAX820TEPE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 3.06V. Reset and low-line threshold accuracy +-2% |
| MAX483ESA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX204EPE | MaximIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MAX303ESE | MaximIC | Precision, dual, high-speed analog switch. |
| MAX6318LHUK34CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.400V min, reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX395EWG | MaximIC | Serially controlled, low-voltage, 8-channel SPST switch |
| MAX6317HUK48DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1.12sec, typ watchdog timeout 1.6sec |
| MAX884C/D | MaximIC | 3.3V or adjustable, low-dropout, low current, 200mA linear regulator. 1microA(max) shutdown(OFF) mode. |
| MAX4663CWE | MaximIC | 2.5om, quad, SWPST, CMOS analog switch (two NC and two NO switches). |
| MAX6504CMN015-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) -15. |
| MAX471CPA | MaximIC | Precision, high-side current-sense amplifier. Precision internal sense resistor. 3A sense capability with internal sense resistor. |
| MAX6318MHUK36AW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX6348XR39-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 3.900V. Order increment 10k |
| MAX6320PUK46CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX3188EEUT-T | MaximIC | +-15kV ESD-protected, 1Mbps, 1microA RS-232 transmitter. |
| MAX712C/D | MaximIC | NiCd/NiMH battery fast-charge controller (by detecting zero voltage slope). |
| MAX4274BHEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 40, 1+ (Rf/Dg) noninverting gain 41, -3dB BW 390kHz. |
| MAX6713TEXS-T10 | MaximIC | Microprocessor reset circuit with manual reset input. Reset threshold 3.08V. Output type active-low open-drain reset. |
| MAX350CPN | MaximIC | Serially controlled, low-voltage, dual 4-channel multiplexer |
| MX7537CQ | MaximIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-1 LSB. |
| MAX6310UK25D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 2.438(min),2.563(max). Nominal timeout period 20ms. |
| MAX6316LUK26CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX1291AEEI | MaximIC | 250ksps, +3V, 8-channel single-ended/4channel pseudo-differential, 12-bit ADC with +2.5V reference and parallel interface INL(LSB) +0.5,-0.5 |
| MAX4507CPN | MaximIC | Fault-protected, high-voltage, signal-line protector |
| MAX6345MUT-T | MaximIC | Microprocessor reset circuit with power-fail comparator. Reset threshold 4.38V. Push-pull active-low reset output, push-pull active-high reset output. |
| MX7548JCWP | MaximIC | CMOS 8-bit microprocessor compatible 12-bit DAC. Linearity +-1 LSB. |
| MAX6319MHUK39C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms |
| MAX216CWN | MaximIC | Low-power AppleTalk interface transceiver. |
| MAX810REUR-T | MaximIC | Microprocessor reset circuit. Reset threshold 2.63V. Push-pull active-high reset. 2.5k increments. |
