| 型號 | 品牌 | 功能應用 |
|---|
| MAX6318LHUK39AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.900V min, reset timeout 1ms,typ watchdog timeout 6.3ms |
| MAX7413CUA | MaximIC | 5th-order, lowpass, switched-capacitor filter. Filter response bessel, operating voltage +3V |
| MAX6322HPUK36D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1120ms |
| MAX712MJE | MaximIC | NiCd/NiMH battery fast-charge controller (by detecting zero voltage slope). |
| MAX3490EESA | MaximIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 12Mbps. Supply voltage 3.0V to 3.6V |
| MAX4514C/D | MaximIC | Low-voltage, low-on-resistance, SPST, CMOS analog switch. Normally open (NO), +2V to +12V single-supply operation. |
| MAX696CWE | MaximIC | Microprocessor supervisory circuit. Battery backup power switching. |
| MAX6321HPUK27BY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| ICL7622ACSD | MaximIC | Dual operational amplifier, 2mV |
| MXD1013C/D075 | MaximIC | 3-in-1 silicon delay line. Output delay 75ns. |
| MAX4282EUA | MaximIC | Dual, open-loop, unity-gain stable amplifier |
| MAX6313UK50D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.875(min) 5.125(max).Nominal timeout period 20ms. |
| MAX674CSA | MaximIC | +10V precision voltage reference. Temp. coefficient ppm/degC 12. Initial error 15mV |
| MAX406BCSA | MaximIC | 1.2microA max, single, single-supply op amp. |
| MAX520BEPE | MaximIC | Quad, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 2. |
| MAX153EWP | MaximIC | 1Msps, microprocessor-compatible, 8-bit ADC with 1microA power-down. |
| MAX706PESA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-high reset output signal. |
| MAX6318MHUK27BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX6359LTUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.63V (Vcc5) and 3.08V (Vcc3). Active-low push-pull reset 5V. Watchdog timer. |
| MAX817LESA | MaximIC | +5V microprocessor supervisory circuit. Reset threshold 4.65V, active-low reset, backup-battery switchover, power-fail comparator, watchdog input, battery freshness seal. |
| MAX6321HPUK46BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX6318MHUK31AY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX4504ESA | MaximIC | Low-voltage, dual-supply, SPST, CMOS analog switch. |
| MAX4311ESD | MaximIC | = +1V/V |
| MAX6311UK00D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,2 additional undervoltage reset inputs,). Nominal timeout period 20ms. |
| MAX202ECWE | MaximIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX6346UR44-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.380V. Standard version. Order increment 2.5k |
| MAX4251ESA | MaximIC | Single, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 3MHz, min stable gain 1V/V, with shutdown. |
| MAX8213BCPE | MaximIC | Five universal voltage monitor - complete microprocessor voltage monitoring. Open-drain outputs. |
| MAX140CMH | MaximIC | 3 1/2 digit A/D converter with bandgap reference and charge-pump voltage converter |
